Page 1 of 2
32 input connector to DIY stereo-jack w/out PCB
Posted:
Thu Feb 26, 2009 2:07 pmby ole_hansen
i'm finding it semi confusing to connect the 32 input connector to the stereo jacks i purchased.
i know how stereo jacks works, but looking at Synthex's "v2.8 Quick Manual", i'm reading
1 - GND
2 - HiHat controller High impedance input
3 - HiHat controller Power source
4 - HiHat controller Low impedance input
5 - Kick
6 - NC
7 - HiHat Bow
8 - HiHat Edge
9 - Snare Head
10 - Snare Rim
11 - Ride Bow
12 - Ride Edge
13 - Crash Bow
14 - Crash Edge
15 - Tom1 Head
16 - Tom1 Rim
etc..etc...
so i'm guessing at least the GND is connector to ALL ground points on each jack, correct?
and then ie. solder #5 to the tip connection of the KickDrum input trigger jack?
and is it still correct that the 32 input connector (on Synthex's v2.8 boards) are connected as shown here:
2 - 4 - 6 - 8......
1 - 3 - 5 - 9......
(when looking from the top down - with the "square" being #1) ?
Re: 32 input connector to DIY stereo-jack w/out PCB
Posted:
Thu Feb 26, 2009 2:26 pmby Synthex
ole_hansen wrote:so i'm guessing at least the GND is connector to ALL ground points on each jack, correct?
Yes.
ole_hansen wrote:and then ie. solder #5 to the tip connection of the KickDrum input trigger jack?
Yes.
ole_hansen wrote:and is it still correct that the 32 input connector (on Synthex's v2.8 boards) are connected as shown here:
2 - 4 - 6 - 8......
1 - 3 - 5 - 9......
(when looking from the top down - with the "square" being #1) ?
Yes.
Re: 32 input connector to DIY stereo-jack w/out PCB
Posted:
Thu Feb 26, 2009 2:28 pmby jman 31
Deleted
Re: 32 input connector to DIY stereo-jack w/out PCB
Posted:
Thu Feb 26, 2009 2:35 pmby ole_hansen
thanks!
gosh darnit i LOVE this forum.
Re: 32 input connector to DIY stereo-jack w/out PCB
Posted:
Thu Feb 26, 2009 2:36 pmby Synthex
jman 31 wrote:Here's the schematic.
INPUTS
NO NO and NO !
This is not the schematics for the Synthex's All In One Kit.
Re: 32 input connector to DIY stereo-jack w/out PCB
Posted:
Thu Feb 26, 2009 3:00 pmby ole_hansen
Synthex wrote:jman 31 wrote:Here's the schematic.
INPUTS
NO NO and NO !
This is not the schematics for the Synthex's All In One Kit.
wow.. thanks for saying that
i could see by checking - but thanks. jman - possibly delete your post for future reference, eh?
Re: 32 input connector to DIY stereo-jack w/out PCB
Posted:
Thu Feb 26, 2009 3:59 pmby jman 31
Whoops, sorry! I guess I need to read a little bit better!
Re: 32 input connector to DIY stereo-jack w/out PCB
Posted:
Thu Feb 26, 2009 4:09 pmby jman 31
Are there schematics for these inputs? or is that something you get when you buy the kit? I did a little plundering around and I couldn't seem to find any.
Re: 32 input connector to DIY stereo-jack w/out PCB
Posted:
Thu Feb 26, 2009 4:24 pmby Synthex
jman 31 wrote:Are there schematics for these inputs? or is that something you get when you buy the kit? I did a little plundering around and I couldn't seem to find any.
All is in the PDF file "Quick Manual v2" on the main "v2.8 All In One Kit" topic.
Re: 32 input connector to DIY stereo-jack w/out PCB
Posted:
Thu Feb 26, 2009 4:30 pmby ole_hansen
the v2 manual for your kit have a fault i believe.
the 32 pinout connector on page 2 (top right) shows it like i asked if was right:
2 - 4 - 6 - 8......
1 - 3 - 5 - 9......
but on page 4 at the bottom it shows the 2 rows of input connectors (2 x 16 pins) to be like this on top of eachother:
1 - 2 - 3 - 4....
21-22-23-24...
